Hydraulic entire press, the entire press of the silicon steel, silicon steel of motor press, the entire press of the motor silicon steel, the entire press of the motor stator silicon steel stator silicon steel the entire press manufacturers 

 Features: 

 A hydraulic system accessories all imported from Taiwan, accessories, protection equipment with low noise, low temperature; 
 Hydraulic system and design of the machine as a whole, the intuitive observation of system components, maintenance and easy maintenance; 
 (3) around the machine nets blockade, you can watch the fuel tank of action is also beneficial to the heat, and safe and reliable; 
 4 cylinder stroke, velocity, pressure can be adjusted for simple operation; 
 Safety is well-designed, using both hands with the emergency button and the upper and lower mold inching to facilitate installation and calibration of the mold according to customers' requirements to install Gauntlets optoelectronics, to make the operation safer; 

 (6) The machine has automatic sensing devices, after the forming of the silicon steel sheet by the automatic high-speed punch to suppress the use of the conveyor belt sent to this machine, the machine sensing products to run automatically, greatly improving production efficiency. 
 Technical parameters: 
 Effective working area: 500 * 400mm 
 Maximum opening height: 300mm 
 Cylinder stroke: 200mm adjustable 50mm 
 Up and down speed: 130mm / s 
 Maximum output :1-20T adjustable 
 Motor power: 3.7kw 
 Operating voltage: AC380V 50/60HZ 
 Fuel tank capacity: 180L 
 Levelers of the stator, the stator silicon steel sheet leveling machine safety operation: 
 A. The operator be familiar with the general properties and structure of the hydraulic press to prohibit the use of overload; 
 Two. Before use, in accordance with the provisions of lubricating oil, check the high-pressure pump, pressure gauge, a variety of valves, seals, etc. is normal; 
 3. Before starting to check the mold supporting material weight to meet the requirements, said the material tool is accurate; 
 4. Touch with oppression must be placed in the position of the plate center, ban eccentric use. Each class before starting the pressure test should be checked once mold is a split loss and abnormal; 
 5 Double operation, set the hand to boot, mutual coordination and cooperation; 
 6. Hands, head placed between the mold and the pressure head is strictly prohibited; 
 7. Work is completed, will pressure products, tools, dies in order and placed in the designated place. 
 Levelers of the stator, the stator silicon steel sheet leveling machine operating system: 
 Operator to have appropriate qualifications, must be certified, is strictly prohibited personnel open the machine do not understand the use of hydraulic machine; 
 Two classes should wear good provisions, supplies and labor protection; 
 3, before starting the examination preparation: photoelectric protection device is reliable, the trip switch is sensitive, the fasteners are loose; 
 4, before starting to remove the debris on work surfaces and mold, to adjust the working pressure, slide stroke, empty running one to two minutes, everything is normal before work; 
 5, the adjustment handle on the machine have been adjusted at the factory fit, non-commissioning can not be arbitrarily adjusted. 
 Levelers of the stator, stator silicon steel sheet leveling machine maintenance system: 
 1, according to the lubrication of machines require routine lubrication and maintenance. 
 2, machine tools per work year later, the hydraulic oil should be released from the bed tank cleaning tank, refill after filtration of hydraulic oil, the oil should be identified in the oil the subject of 3/4 height; 
 3, the oil filter on the suction pipe network, each quarter must be cleaned once; 
 4, on a regular basis to check the handle, knob, button is damaged, if damaged, replaced at any time; 
 5, the motor must be kept clean, the motor of the air inlet grille need to keep good ventilation condition; 
 6, the day the first 10 minutes, clean the machine and lubrication activities in parts; 
 7, forbidding the operator to operate the equipment, usually must be done to stop away from the machine. 
 The four-column hydraulic machine is widely used in the stereotypes of the automotive industry, spare parts processing and the industry a variety of products, red edge, correction and footwear, handbags, rubber, molds, shafts, bushings class parts of the press-fit, embossing, bent sheet metal parts, stamping, shaped stretching process, washing machines, electric motors, car motors, air conditioning motors, micro motors, servo motors, wheels manufacture, shock absorber, motorcycle and machinery and other industries. 

 Scope of application: 

 Professional for the stator leveling. 

 Fluid to move the entire press, the entire press of the silicon steel, silicon steel of motor press, the entire press of the motor silicon steel, the entire press of the motor stator silicon steel stator silicon steel sheet press manufacturers - Shenzhen Xin Gou quality protection !